Lenox Carbide Grit Hole Saws
Lenox Master-Grit Hole Saws
CUTS ABRASIVE MATERIALS
Tungsten carbide grit cuts through fiberglass, ceramic tile, laminates and other abrasive materials
CLEAN CUTTING
Carbide grit edge will not snag or chip when cutting thin materials
Use standard arbor or SNAP-BACK™ arbor
SPECIFICATIONS:
| 1 PER BOX | DIAMETER | PIPE TAP | PIPE ENTRANCE | USE ARBOR | ||||||
|---|---|---|---|---|---|---|---|---|---|---|
| PROD NO | IN | MM | IN | MM | IN | MM | SNAP BACK | STANDARD | ||
| 2991212CG | 3/4 | 19.1 | 1/2 | 12.7 | 3/8 | 9.5 | — | 1L or 4L | ||
| 2999820MMCG | 25/32 | 19.8 | — | — | — | — | — | 1L or 4L | ||
| 2991414CG | 7/8 | 22.2 | 3/4 | 19.1 | 1/2 | 12.7 | — | 1L or 4L | ||
| 2991616CG | 1 | 25.4 | — | — | — | — | — | 1L or 4L | ||
| 2991818CG | 1-1/8 | 28.6 | 1 | 25.4 | 3/4 | 19.1 | — | 1L or 4L | ||
| 2992020CG | 1-1/4 | 31.8 | — | — | — | — | 2L | 2L | ||
| 2992222CG | 1-3/8 | 34.9 | — | — | 1 | 25.4 | 2L | 2L | ||
| 2992424CG | 1-1/2 | 38.1 | 1-1/4 | 31.8 | — | — | 2L | 2L or 7L | ||
| 2992828CG | 1-3/4 | 44.5 | 1-1/2 | 38.1 | 1-1/4 | 31.8 | 2L | 2L or 7L | ||
| 2993232CG | 2 | 50.8 | — | — | 1-1/2 | 38.1 | 2L | 2L or 7L | ||
| 2993434CG | 2-1/8 | 54 | — | — | — | — | 2L | 2L or 7L | ||
| 2993636CG | 2-1/4 | 57.2 | 2 | 50.8 | — | — | 2L | 2L or 7L | ||
| 2993838CG | 2-3/8 | 60.3 | — | — | — | — | 2L | 2L or 7L | ||
| 2994040CG | 2-1/2 | 63.5 | — | — | 2 | 50.8 | 2L | 2L or 7L | ||
| 2994141CG | 2-9/16 | 65.1 | — | — | — | — | 2L | 2L or 7L | ||
| 2994848CG | 3 | 76.2 | — | — | 2-1/2 | 63.5 | 2L | 2L or 7L | ||
| 2995252CG | 3-1/4 | 82.6 | 3 | 76.2 | — | — | 2L | 2L or 7L | ||
| 2995858CG | 3-5/8 | 92.1 | — | — | 3 | 76.2 | 2L | 2L or 7L | ||
| 2996464CG | 4 | 101.6 | — | — | — | — | 2L | 2L or 7L | ||
| 2996666CG | 4-1/8 | 104.8 | — | — | 3-1/2 | 88.9 | 2L | 2L or 7L | ||